4.1.5 Finish for sheet in nonheat-treatable alloys (Section 1). HR - Hot Rolled ... Thickness, Inches. 36 48 - 60 72 3/16 .181 N/A .015 .016 Length Thickness Tolerance Coil. ASTM-AISI-Thickness-Tolerance-Ranges.pdf Download.0236 plus .008 is considered to be 24 ga.0236 plus .004 is considered the nominal for 24 ga.0236 + .004 = .0276.0276 * 41.88 lb (weight of carbon steel) per cubic ft * 40 sq ft (4’x10′ sheet) = 46.24# Actual Weight – actual scale weight of the coil. 4.1.7 Dimensions (thickness, width, and length or coil size). 3. The following charts give typical ASTM and ANSI steel sheet mechanical tolerance ranges. Mild Steel ASTM A283 Cold Rolled Plates: Mild Steel IS 2062 GR.A Chequered Plates: ASTM A36 Mild Steel Plates Suppliers: ASME IS 2062 GR.A Mild Steel Plate 2B Finish Dealer: Mild Steel ASTM A283 CR Plates Stockholder: Mild Steel IS 2062 GR.B Hot Rolled Plates Dealer: Mild Steel IS 2062 GR.A HR Plates: ASTM A283 Mild Steel Plates Exporter ASTM A480hot rolled sheet/coil thickness tolerance. thcikness ，in. Metric Hex Bars : Spec. [mm]: Deviation, allowed for the specified width 4.1.6 For sheet, whether flat or coiled. 6061 Aluminum Plate Tolerance Chart Flatness Size Thickness LBS/ Sq. 4.2 Additionally, orders for material to this specification shall include the following information when required by the purchaser: Tolerance Range. ASTM A6 - ASME SA6 Thickness Tolerances of Steel Plates - Free download as PDF File (.pdf), Text File (.txt) or read online for free. Minimum Thickness Purchased, in. ASTM A240 A480 steel sheet'sthickness tolerance. Stainless Steel: Hex Bar (Metric) 304, 316 Cold Finish >3mm to ≤6mm 0/-.075mm: Stainless Steel: Hex Bar (Metric) 304, 316 Decimal Equivalent. Specified width mm *The thickness tolerance for floorplate is for the unraised thickness of the plate. Width tolerances for plates with trimmed edges are given in Table 2: Table 2: Tolerance over width and length for sheared edges Nominal thickness t (mm) Tolerances on the width Lower Upper 4,5 < t < 5,0 0 +20 6,0 < t < 10 0,0 0 +25 Width tolerances for plates with untrimmed edges shall be agreed at the time of ordering. Tolerances below are for coil product, applies to the following alloys: (253, 330, 333, 304, 309, 316, 321, 347, 410, 446, 2205, 2507, 2101, 17-4, 17-5, 800) Tolerances listed were taken from ASTM A480 (Reference Only) Hot Rolled Sheet / Coil Tolerance Over Specified Minimum, in. Lbs/Ft 2. Across Flats, mm Across Flats Tol. Note: PLATE AND FLOORPLATE ROLLED ON A PLATE MILL Thickness tolerances given are applicable to plate and floorplate in all edge conditions, with a specified or typical minimum yield strength of 360 MPa or less. Tolerance under specified thickness .010" x 3/4 x 52" wide plate, for example, would have a tolerance range of .740-.780" Because of tolerances, ie thickness, flatness and camber, as well as the hot roll condition, ASTM A36 generally does not finish to specified thickness. For thickness measured at any location other than that specified in Note 2, the permissible maximum over tolerance shall be increased by 75%, rounded to the nearest 0.01 in. Ft. Estimate Lbs/Plate Estimate Plates Per Skid Exact. ASTM ANSI Mechanical Steel Sheet Mechanical Tolerances. 1. STRIP MILL PLATE THICKNESS TOLERANCES Thickness in. Title: Aluminum Plate Tolerances.xlsx Author: MHumpal Created Date: Weight. ASTM International Committees A01 on Steel, Stainless Steel and Related Alloys and A05 on Metallic-Coated Iron and Steel Products recently approved revisions to two standards that clarify the thickness tolerances for both uncoated and coated steel sheet products. ASTM-AISI Thickness Tolerance Ranges. Mechanical Steel Sheet Mechanical Tolerances Metals and Materials | Metal Products Distributor Supplier. Tolerancias espesores 3. Steel Sheet Thickness Tolerances.